GR12 Titanium Rods for Corrosion-Resistant Components

GR12 Titanium Rods for Corrosion-Resistant Components

Alloy Designation: GR12 / Ti-0.3Mo-0.8Ni. TA10 requirements specified for GB/T supply.
Size Range: Diameter 6–200 mm, length up to 3,000 mm. Custom dimensions by agreement.
Manufacture: Rolled solid bar with a machined exterior.
Surface Requirements: Finish and any specified roughness are confirmed against the intended use.
Application Direction: Bar stock for corrosion-resistant equipment parts, subject to engineering approval.
Product Specification: ASTM B348 or GB/T 2965-2023, with the required delivery condition stated.
Order Information: Minimum 10 kg. Quotations cover the selected dimensions, inspection scope and packing requirements.
Send Inquiry
Product Introduction

Look Beyond the Exposed Surface

Corrosion does not always develop evenly across a component. A joint can retain liquid while the surrounding surface remains freely exposed. Beneath a seal or within a close-fitting assembly, the local environment may differ from the bulk solution.

GR12 is a titanium alloy containing nominal additions of 0.3% molybdenum and 0.8% nickel. Compared with unalloyed titanium, it offers improved resistance to crevice attack in certain hot chloride solutions. This is a reason to evaluate GR12 for components where local exposure conditions influence material selection.

Match the Assessment to the Corrosion Mechanism

Design concern What needs to be established
General metal loss Suitability for the complete liquid composition and temperature
Crevice attack Conditions within seals, contacts and retained-liquid areas
Combined loading and exposure Mechanical requirements alongside corrosion performance

A low corrosion rate measured in one salt solution cannot establish performance in every chloride-containing process. Nor does resistance to crevice attack mean that the material prevents deposits or biological growth.

Solid Bar for the Specified Component

Our rods provide starting material for equipment parts such as pins, sleeves and fastener blanks where GR12 is specified. Tubes, vessel linings and sheet components are separate product forms.

For a new duty, provide the operating medium, concentration range, temperature and a description of the exposed assembly. Where existing data are insufficient, a representative test can be defined with the customer's engineer.

Any corrosion-performance requirement should identify the test method and acceptance limit. Material chemistry and mechanical inspection remain governed by the agreed bar specification; they do not independently predict equipment life.

Corrosion-Resistant GR12 Titanium Rod FAQ

When should GR12 be considered instead of commercially pure titanium?

GR12 deserves evaluation when hot chloride exposure and crevice conditions influence material selection. Its molybdenum and nickel additions improve resistance to crevice attack in certain environments. Provide the operating temperature, fluid composition and assembled component geometry so the material choice can be assessed against the actual duty.

Does a low corrosion rate in seawater establish suitability for a chemical process?

Chemical-process conditions require their own assessment. Concentration, acidity, contaminants and temperature can differ substantially from seawater. Include the full process composition and expected changes during operation. Where a comparison uses published corrosion data, check that the test conditions represent the proposed service.

What should I specify for a GR12 sleeve or pin installed in a close-fitting joint?

Provide the finished drawing, mating materials, fits and surface requirements. Identify where liquid can enter or remain trapped, including beneath seals and around contact surfaces. The design review should consider local exposure alongside loading, wear and the clearances needed for assembly.

How should a corrosion test represent crevices in the finished component?

Agree the specimen arrangement with the responsible materials engineer. Relevant details include the contacting material, crevice geometry, solution composition, temperature and exposure duration. Define the inspection method and acceptance limit before testing so the results can support the intended material decision.

Which records are needed to accept GR12 rod for a corrosion-sensitive order?

Specify the material standard, grade, delivery condition and required chemical and mechanical test records. Include heat or batch identification and any agreed surface or internal examination. If corrosion testing forms part of approval, identify it separately with its test conditions and acceptance criteria.

Can GR12 be substituted for another alloy in an existing component?

A substitution requires review of both the material specification and the equipment design. Check corrosion compatibility, mechanical properties, thermal behaviour, mating materials and joining requirements. Provide the original specification and proposed operating duty so the responsible engineer can establish the approval requirements.

Hot Tags: GR12 Titanium Rods for Corrosion-Resistant Components, China GR12 Titanium Rods for Corrosion-Resistant Components manufacturers, suppliers, factory

Send Inquiry

whatsapp

Phone

E-mail

Inquiry